DonnyFL
DonnyFL | EMPEROR V3/RONIN 6.26 EXTENDER
$59.99
Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it's the latest model.
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | FATBOY 2.0 Extension/Extender Tube
$39.99
Need to make the fat boy quieter? You can add this 3 inch extender to capture more air and reduce the muzzle blast some more.
Features:
6061 T6 Aluminum
Black anodize
Matching outer tube design to the fat boy
Also compatible with the Ronin and Emperor
DonnyFL
AEA | HP & SF Series | Moderator Adapter #A77
$39.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
Works on AEA HP/SF models & HP SS MAX .30 CAL ONLY
Features:
6061 Aluminum
1/2 x 20 male threads
Black Anodized
DonnyFL
AEA | HP SS Max .357 Cal | Challenger "BIG BORE" .357/.45/.50 Cal #A91 Moderator Adapters
$39.99
This adapter is compatible with the .35/.45/50 Cal AEA Challenger "BIG BORE" (side lever model only) as well as the .357 AEA HP SS Max. #A91
*The HP SS MAX 45/50 does not need an adapter*
Features:
M18x1 male threads
6061 T6 Aluminum
Anodized
Knurled thread protector
DonnyFL
AEA | Challenger Pro Moderator Adapter #A99
$34.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
This adapter converts the factory barrel threads from M14x1 to 1/2 x 20. It is also designed to center the barrel within the shroud.
Features:
6061 T6 Aluminum
Not anodized
Compatible up to .30 caliber
DonnyFL
Air Venturi Avenger Extender/Umarex Origin 1/2 x 20 Adapter #A70
$44.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF**DOES NOT FIT ANY OF THE AVENGER X SERIES GUNS**
This version allows you to use a larger suppressor than the Tanto or KOI without having to remove it to fill the gun. Also redesigned to slide over the barrel to keep the barrel centered with the adapter. This reduces the chance of pellet clipping and improves accuracy.
Features:
Compatible with .177 caliber to .25
6061 Aluminum T6
Black anodized
1/2 x 20 male threads
*Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping.
DonnyFL
DonnyFL | FATBOY 2.0 Muzzle Brake
$29.99
This muzzle brake or air stripper screws onto the front of the fat boy.
Note: This unit does not come with the individual air strippers. You can change the caliber size by using the inserts that was included with the fat boy.
Features:
Made of aluminum 6061 T6
Black anodize
Weights 2.9 oz
Add the optional 3 inch extender for the Fatboy to make it quieter!EXTENDER!
DonnyFL
AEA | Challenger Series | .22/.25/.30 & .357 Moderator Adapters | #A81 & #A83
$39.99
Adapters are threaded for attaching a moderator
*DOES NOT WORK WITH THE 32" CHALLENGER STANDARD OR BULLPUP. THE 32" DOES NOT HAVE A SHROUD AND A 1/2x20 UNF MODERATOR CAN BE SCREWED DIRECTLY ON WITHOUT A ADAPTER*
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Comes with knurled thread protector
For .30 caliber measure the OD of the threaded part of the front cap. It should be close to 28mm. May need to heat up the front cap with a heat gun or mini torch to loosen the thread locker.
DonnyFL
AEA | Challenger Pro Moderator Adapter M14x1 A100
$34.99
Adapters are threaded for attaching a moderator
This end cap is for your Ronin or Emperor to screw directly onto the AEA Challenger pro shroud. It has a recess that helps center the barrel inside the shroud.
Features:
6061 T6 Aluminum
compatible with all Challenger Pro barrels
DonnyFL
AEA | Terminator M18x1 Big Bore Adapter #A64
$39.99
Adapters are threaded for attaching a moderator
Thread: M18 x 1
Works on AEA TERMINATOR models.
You may need to heat up the front cap to loosen the epoxy. Then unscrew from gun.
DonnyFL
Benjamin Bulldog .357 Cal Moderator Adapter w/ thread protector #A41
$44.99
Adapters are threaded for attaching a moderator
Thread: M18 x 1
The new adapter have finally arrived. This new design goes back to the barrel and slides over the barrel bushing. This will keep the barrel aligned with the adapter's exit hole. Please note that the barrel bushing is not included.
The .357 Benjamin Bulldog is becoming popular for big game hunting. Add this adapter and pair it up with a .357 Ronin or .357 Emperor to make it the ultimate hunting airgun.
The factory gun already has the barrel bushing. I took mime off to show how it fits into the adapter in the picture.
Made by CNC for accuracy
Very easy to install. Remove the top and bottom screw securing the front cap and swap it out for this adapter. Screw the two screws back in and you're done. No need to remove the shroud.
Matte Black anodize
Knurled thread protector
When putting this on, press the adapter into the shroud as you tighten the two screws. This will ensure the adapter is flush with the shroud.
DonnyFL
FX/DonnyFL Moderator
$119.99
This is a custom size that comes with your FX guns if you decide to upgrade the suppressor. Same length as the Tanto but larger in diameter. The outer diameter is comparable to the FX factory suppressor.
Features:
1.36 x 5 inches
Available in .25 & 30
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
We don't recommend using this with the FX Panthera or FX Panthera Hunter.
DonnyFL
Benjamin Marauder (Mrod) | Fortitude | Armada Moderator Adapter #A7
$39.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
Marauders are great entry level PCP guns. Lots of mods you can do to make them more powerful. More power means a louder gun. To make it backyard friendly make sure to grab this 1/2 x 20 UNF Adapter to allow you to screw on an aftermarket LDC. Threaded end that goes into the OEM shroud is 13/16 - 28.
*Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
DonnyFL
Hatsan Blitz M18 X 1 Adapter A117
$39.99
This adapter allows you to screw on an airgun suppressor with M18x1 threads.
***New Improved For More Air Flow.***
I recommend going with the Ronin with this gun. I have it installed on my personal gun and it works flawlessly. However, results may vary and might need modification to work in semi auto mode. This gun is similar to the Bullmaster and others have been able to fix the issue by replacing the spring. Go to your hardware store and look for a lighter spring. I got mine from Ace hardware and it fixed the magazine indexing issue.
Features:
Compatible up to .30 caliber
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
DonnyFL
Hatsan QE Moderator Adapter A24
$44.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
Please note: I highly suggest getting a suppressor one size up from what your gun is. For example if you have a .25, get a .30. If you have a .30, the .30 cal suppressor is fine. This is to minimize the chance of the gun clipping.
Also if you have a Hatsan Bully .25/.30, based on customer's feedback I would go with the Emperor.
*We have not had any success with customers using a suppressor on Hatsan's line up of semi auto guns. It causes the gun to not index properly.
Features:
Matte black Anodized
CNC
Includes knurled thread protector
Compatible up to .30
Compatible with the following guns:
Hatsan GladiusHatsan Flash Wood QEHatsan AirMaxHatsan Bullboss QEHatsan BT65 QEHatsan Nova QEHatsan AT44-10 QEHatsan Hercules QEHatsan Flashpup QEHatsan AT P1Hatsan Flash QE