DonnyFL
AEA | HP & SF Series | Moderator Adapter #A77
$39.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
Works on AEA HP/SF models & HP SS MAX .30 CAL ONLY
Features:
6061 Aluminum
1/2 x 20 male threads
Black Anodized
DonnyFL
AEA | HP SS Max .357 Cal | Challenger "BIG BORE" .357/.45/.50 Cal #A91 Moderator Adapters
$39.99
This adapter is compatible with the .35/.45/50 Cal AEA Challenger "BIG BORE" (side lever model only) as well as the .357 AEA HP SS Max. #A91
Features:
M18x1 male threads
6061 T6 Aluminum
Anodized
Knurled thread protector
DonnyFL
AEA | Challenger Pro Moderator Adapter #A99
$34.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
This adapter converts the factory barrel threads from M14x1 to 1/2 x 20. It is also designed to center the barrel within the shroud.
Features:
6061 T6 Aluminum
Not anodized
Compatible up to .30 caliber
DonnyFL
Air Venturi Avenger Extender/Umarex Origin 1/2 x 20 Adapter #A70
$44.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF**DOES NOT FIT ANY OF THE AVENGER X SERIES GUNS**
This version allows you to use a larger suppressor than the Tanto or KOI without having to remove it to fill the gun. Also redesigned to slide over the barrel to keep the barrel centered with the adapter. This reduces the chance of pellet clipping and improves accuracy.
Features:
Compatible with .177 caliber to .25
6061 Aluminum T6
Black anodized
1/2 x 20 male threads
*Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping.
DonnyFL
DonnyFL | END CAP/QD ADAPTER
from $20.00
FEATURES:
Rear caps for existing moderators
M71 = Sumo/Tatsu/Shogun QD rear cap with 1/2 x 20M72 = Ronin/Emperor/ Fat Boy QD rear cap with 1/2 x 20M73 = KOI/Tanto QD rear cap with 1/2 x 20M74 = FX/DonnyFL QD rear cap with 1/2 x 20M86 - Ronin/Emperor QD rear cap with M18x1
M87= FX/DonnyFL QD rear cap with M18x1
QD AdaptersM75 = QD barrel adapter M14x1.25M76 = QD barrel adapter M18x1M77 = QD barrel adapter M20x1M78 = QD barrel adapter 1/2 x 20
Product details:
Indexed so it locks on at same position every time
Made of 7075 aluminum
Grey anodized
Includes barrel/shroud adapter and rear cap
Select the barrel thread specific to your airgun
DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.Compatibility: Will not work on old moderators with the flat front cap.
DonnyFL
AEA | Challenger Series | .22/.25/.30 & .357 Moderator Adapters | #A81 & #A83
$39.99
Adapters are threaded for attaching a moderator
*DOES NOT WORK WITH THE 32" CHALLENGER STANDARD OR BULLPUP. THE 32" DOES NOT HAVE A SHROUD AND A 1/2x20 UNF MODERATOR CAN BE SCREWED DIRECTLY ON WITHOUT A ADAPTER*
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Comes with knurled thread protector
For .30 caliber measure the OD of the threaded part of the front cap. It should be close to 28mm. May need to heat up the front cap with a heat gun or mini torch to loosen the thread locker.
DonnyFL
AEA | Challenger Pro Moderator Adapter M14x1 A100
$34.99
Adapters are threaded for attaching a moderator
This end cap is for your Ronin or Emperor to screw directly onto the AEA Challenger pro shroud. It has a recess that helps center the barrel inside the shroud.
Features:
6061 T6 Aluminum
compatible with all Challenger Pro barrels
DonnyFL
Benjamin Marauder (Mrod) | Fortitude | Armada Moderator Adapter #A7
$39.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
Marauders are great entry level PCP guns. Lots of mods you can do to make them more powerful. More power means a louder gun. To make it backyard friendly make sure to grab this 1/2 x 20 UNF Adapter to allow you to screw on an aftermarket LDC. Threaded end that goes into the OEM shroud is 13/16 - 28.
*Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
DonnyFL
Benjamin Bulldog .357 Cal Moderator Adapter w/ thread protector #A41
$44.99
Adapters are threaded for attaching a moderator
Thread: M18 x 1
The new adapter have finally arrived. This new design goes back to the barrel and slides over the barrel bushing. This will keep the barrel aligned with the adapter's exit hole. Please note that the barrel bushing is not included.
The .357 Benjamin Bulldog is becoming popular for big game hunting. Add this adapter and pair it up with a .357 Ronin or .357 Emperor to make it the ultimate hunting airgun.
The factory gun already has the barrel bushing. I took mime off to show how it fits into the adapter in the picture.
Made by CNC for accuracy
Very easy to install. Remove the top and bottom screw securing the front cap and swap it out for this adapter. Screw the two screws back in and you're done. No need to remove the shroud.
Matte Black anodize
Knurled thread protector
When putting this on, press the adapter into the shroud as you tighten the two screws. This will ensure the adapter is flush with the shroud.
DonnyFL
Hatsan Blitz M18 X 1 Adapter A117
$39.99
This adapter allows you to screw on an airgun suppressor with M18x1 threads.
***New Improved For More Air Flow.***
I recommend going with the Ronin with this gun. I have it installed on my personal gun and it works flawlessly. However, results may vary and might need modification to work in semi auto mode. This gun is similar to the Bullmaster and others have been able to fix the issue by replacing the spring. Go to your hardware store and look for a lighter spring. I got mine from Ace hardware and it fixed the magazine indexing issue.
Features:
Compatible up to .30 caliber
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
DonnyFL
AEA | Terminator M18x1 Big Bore Adapter #A64
$39.99
Adapters are threaded for attaching a moderator
Thread: M18 x 1
Works on AEA TERMINATOR models.
You may need to heat up the front cap to loosen the epoxy. Then unscrew from gun.
DonnyFL
Hatsan QE Moderator Adapter A24
$44.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
Please note: I highly suggest getting a suppressor one size up from what your gun is. For example if you have a .25, get a .30. If you have a .30, the .30 cal suppressor is fine. This is to minimize the chance of the gun clipping.
Also if you have a Hatsan Bully .25/.30, based on customer's feedback I would go with the Emperor.
*We have not had any success with customers using a suppressor on Hatsan's line up of semi auto guns. It causes the gun to not index properly.
Features:
Matte black Anodized
CNC
Includes knurled thread protector
Compatible up to .30
Compatible with the following guns:
Hatsan GladiusHatsan Flash Wood QEHatsan AirMaxHatsan Bullboss QEHatsan BT65 QEHatsan Nova QEHatsan AT44-10 QEHatsan Hercules QEHatsan Flashpup QEHatsan AT P1Hatsan Flash QE
DonnyFL
Umarex Hammer M18x1 #A60 Moderator Adapter
$39.99
Adapters are threaded for attaching a moderator
Thread: M18 x 1
This adapter replaces the factory shroud baffle and has M18x1 threads. Comes with thread protector
DOES NOT WORK WITH THE HAMMER CARBINE MODEL
Instructions:
remove the factory shroud by grabbing onto the shroud by the front cap. When you turn the shroud counter clockwise, that should loosen the front cap. The shroud is free floating, there are no threads in it. Important thing is to remove the front cap.
once shroud is off, put a few drops of red loctite onto the barrel thread.
put the shroud back on
now take new shroud adapter and tighten onto barrel. Let it dry for a few minutes
remove thread protector on shroud adapter to screw on an airgun suppressor with M18x1 threads.
huben
Huben | GK1 Pistol Adapter
$24.99
Adapter that allows you to connect a moderator to a GK1 Air Pistol.
DonnyFL
AEA | Element 1/2 x 20 Adapter | #A93
$39.99
This adapter fits factory carbon fiber shroud allowing you to screw on an airgun suppressor with 1/2 x 20 threads.
Features:
6061 Aluminum T6
Black Anodized
Knurled thread protector