DonnyFL
DonnyFL | KOI Moderator
$130.49
$144.99
With a new rugged front cap design, signature DonnyFL body grooves and bolt endcap, the KOI is a great addition to any shrouded or un-shrouded air rifle. This model has the smallest outer diameter compared to the other DonnyFL models but don’t let the size fool you. With the added vent holes around the front, it is as impressive as the others.
Features:
Available in .22/.25 and .30
Mono-core design
Precision CNC’ed by professional machinist
Sand blasted and anodized for maximum durability
Swappable rear end caps for 1/2 x 20 Bolt, FX (M20x1) Bolt or 1/2 x 20 Cone
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling
Weight:
1. With 1/2 x 20 Bolt rear end cap: 4.7 oz2. With 1/2 x 20 Cone rear end cap: 5.0 oz3. With M20x1 Bolt rear end cap: 4.6 oz4. With M14x1.25 Bolt rear end cap: 4.6 oz*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
![DonnyFL | RONIN .357/.457/.50 [BIG BORE] Moderator](http://www.thepelletshop.com/cdn/shop/products/111_f833b5cc-ea70-48e5-bcfa-df3cfeb9484c_10x.jpg?v=1595468752)
DonnyFL
DonnyFL | RONIN .357/.457/.50 [BIG BORE] Moderator
$166.49
$184.99
Ronin for the .357 is a redesign of the Ronin 1/2 x 20. If you do not like the length of the Emperor, this is an awesome alternative. Rear cap was also changed to reduce weight.
2 x 6.25 inches
Available for .357/.457/.50 caliber airguns
M18x1 threaded end cap
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become loose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
Weight 9.7 oz
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | RONIN Moderator
$166.49
$184.99
Ronin is big and bold, but it looks great even on compact bullpups. "Maybe a little overkill for the .177 and .22 but it looks so damn awesome!" - Donny
Available in .25/.30 and .357 (Big Bore) calibers
2 x 6.5 inches
1/2 x 20 UNF, FX(20mm) & Vulcan thread by request.
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become lose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | RYU Moderator
$166.49
$184.99
FEATURES:• Indexed locking system for consistent position and no point of impact changes.• Quick detachment for easy storage and reattachment for shooting.• Comes with a 1/2 x 20 female (barrel/shroud) thread adapter.• Modular design for length adjustment.• Crafted from 6061 T6 aluminum (individual sections) and 7075 aluminum (main QD housing andadapter).• Quick disconnect rear available for the following moderators.(EMPEROR,SUMO,RONIN,SHOGUN,FX,TANTO,TATSU,KOI,FATBOY)
The RYU has the same diameter as our KOI at 30.48mm or 1.2 inches.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | SHOGUN Moderator
$166.49
$184.99
If you thought Sumo was quiet wait until you hear Shogun. Shogun is just like Sumo but 1.5 inches longer. Donny added an additional 1 inch chamber as well as increase the first expansion chamber by .5 inches and the chamber by the exit hole another .5 inches. This design is very effective.
1.6 x 8 inches
Available in .25 and .30 calibers
Available in 1/2x20 UNF, FX(20mm) & Vulcan Thread by request.
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become lose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | SUMO Moderator
$134.99
$149.99
One of the original and most popular moderators made by DonnyFL. Great balance between size and sound suppression !
1.6 x 6.5 inches
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become lose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | TANTO Moderator
$89.99
$99.99
Features:
1.22 x 5 inches
Available in .22/.25 and .30
Mono-core design
Precision CNC’ed by professional machinist
Sand blasted and anodized for maximum durability
Swappable rear end caps for 1/2 x 20 Bolt, FX (M20x1) Bolt or 1/2 x 20 Cone
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling
Tanto with cone endcap is 5.37 inches
Weight:
1. With 1/2 x 20 Bolt rear end cap: 3.9 oz2. With 1/2 x 20 Cone rear end cap: 4.1 oz3. With M20x1 Bolt rear end cap: 3.5 oz*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | TATSU Moderator
$116.99
$129.99
Tatsu or "Dragon" will be a great addition for shooters who need to take the bark out of their gun yet keep the overall length short. This is a smaller version of the popular Sumo. Features:
1.6 x 4.25
Available in .22/.25 and .30
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become loose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
Weight 4.1 oz
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | YOKOZUNA Moderator
$180.00
$200.00
Please note we are currently out of yokozuna boxes, they will be shipped inside of DonnyFL red tubes.
FEATURES:• Indexed locking system for consistent position and no point of impact changes.• Quick detachment for easy storage and reattachment for shooting.• Comes with a female (barrel/shroud) thread adapter.• Modular design for length adjustment.• Crafted from 6061 T6 aluminum (individual sections) and 7075 aluminum (main QD housing andadapter).
•YOKOZUNA: has the same outer diameter as our Sumo 40.46mm or 1.6
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | YOKOZUNA Moderator Threaded Housing
$166.50
$185.00
Please note we are currently out of yokozuna boxes, they will be shipped inside of DonnyFL red tubes.
Product description
If you're a shooter who prefers leaving the same moderator on your airguns but wants the flexibility to customize the length, the DonnyFL YOKOZUNA is perfect. Its modular design allows you to lengthen or shorten the unit according to your dampening needs.
Key Features:
Precision Threads: The 1/2 x 20 threads are designed to seamlessly attach to the barrel of your airgun, ensuring a secure fit and optimal sound suppression performance.
Durable Construction: Crafted from high-quality materials, this airgun moderator is built to withstand the rigors of outdoor use. It's resistant to corrosion, abrasion, and extreme weather conditions.
Enhanced Safety: By reducing the noise generated by your airgun, you can enjoy a safer shooting environment and minimize noise pollution in your surroundings.
Improved Accuracy: The reduction in muzzle report enhances your shooting accuracy, making it easier to hit your target with precision.
Sleek Design: Features a sleek and stylish design that complements the aesthetics of your airgun, making you the envy of fellow shooters.
Easy Installation: The 1/2 x 20 threads make attaching and detaching the moderator a breeze. It fits most airgun barrels with these standard threads, allowing for a hassle-free setup.
Choosing the right size: If you are connecting directly to a threaded barrel, purchase the same size as your airgun. If you are connecting to a shrouded barrel to using an adapter, go one size up.
Specifications:
Dimensions: 1.6 inches (40.64mm) x 7.25 inches (184.15mm)
Weight: 10.3 oz
Why Choose DonnyFL?
Expert Craftsmanship: DonnyFL products are precision CNC machined by professional machinists, ensuring the highest quality and performance.
Innovative Design: Our moderators are designed with cutting-edge features to enhance your shooting experience.
Durability: Built with top-notch materials and finishes, DonnyFL products are made to last.
Customer Satisfaction: We prioritize customer satisfaction with reliable products and excellent customer service.
AEA
AEA Long Range Master | Slugs | .45 Cal
$20.99
AEA Long Range Master Hollowpoint Airgun Slugs Features
.45 cal
Head: .457 mm diameter
Hollowpoint
60 count
*Correct grain is 155 gr- not 116.67 gr as shown in picture*
AEA
AEA Long Range Master | Slugs | .58 Cal
$23.99
AEA Long Range Master Hollowpoint Airgun Slugs Features
.58 cal
Head: .58 mm diameter
Hollowpoint
20 count
DonnyFL
AEA | Challenger Pro Moderator Adapter #A99
$31.49
$34.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
This adapter converts the factory barrel threads from M14x1 to 1/2 x 20. It is also designed to center the barrel within the shroud.
Features:
6061 T6 Aluminum
Not anodized
Compatible up to .30 caliber
DonnyFL
AEA | Challenger Pro Moderator Adapter M14x1 A100
$31.49
$34.99
Adapters are threaded for attaching a moderator
This end cap is for your Ronin or Emperor to screw directly onto the AEA Challenger pro shroud. It has a recess that helps center the barrel inside the shroud.
Features:
6061 T6 Aluminum
compatible with all Challenger Pro barrels
DonnyFL
AEA | Challenger Series | .22/.25/.30 & .357 Moderator Adapters | #A81 & #A83
$35.99
$39.99
Adapters are threaded for attaching a moderator
*DOES NOT WORK WITH THE 32" CHALLENGER STANDARD OR BULLPUP. THE 32" DOES NOT HAVE A SHROUD AND A 1/2x20 UNF MODERATOR CAN BE SCREWED DIRECTLY ON WITHOUT A ADAPTER*
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Comes with knurled thread protector
For .30 caliber measure the OD of the threaded part of the front cap. It should be close to 28mm. May need to heat up the front cap with a heat gun or mini torch to loosen the thread locker.