Saber Tactical
FX MAVERICK / WILDCAT | Cheek Riser ST0046
$44.99
$49.99
Features:
Cheek riser is made of delrin with Aluminum mounting plate
Allows a little over 18mm of vertical adjustment.
Ambidextrous for left and right hand shooters
Weight = 3.6oz
Note* Highly recommend pairing with the standard/compact FX Maverick TRS rail
Saber Tactical
Fx Maverick Double Tank Adapter ST0053
$22.50
$25.00
PRODUCT DESCRIPTION
Pair this adapter with the FX Impact Double tank adapter ST0011 and you can convert your single tank Maverick to a double tank. Please note you will also need an extra air tank.
Features
6061 T6 aluuminum
black anodize
Saber Tactical
Fx Panthera | Drop-down Front Bottle Adapter | ST0060
$53.99
$59.99
The new Saber Tactical adapter allows a bottle to be attached to the front end of the Panthera while continuing to use either the stock Panthera Rail or the Saber Tactical Panthera Rail.
PRODUCT FEATURES
- 7.6oz in weight- Made of 304 Stainless Steele with electroplating
Saber Tactical
Saber Tactical | 34MM BOTTLE CLAMP ST0005
$53.99
$59.99
Product description
If you're uneasy about drilling into your factory gun stock, this 34mm tube clamp will easily attach to your 34mm air reservoir. It has rubber pads on the inside to prevent any marring to your bottle. This clamp has picatinny rails at the bottom for you to connect your preferred picatinny accessories.
Features:
6061 T6 aluminum
Matte black anodize
Compatible with:
FX Wildcat
FX Dreamlime "Tube"
FX Streamline
Taipan Veteran
Benjamin Marauder
Saber Tactical
Saber Tactical | RAW HM1000 Chassis - ST0058
$315.00
$350.00
Note: Does not include rear buttstock. if you have the wooden version, you'll need to source one.
The Saber Tactical Raw HM1000 chassis is the perfect upgrade for your air rifle. Made from high-quality 6061 aluminum, this chassis is both lightweight and durable, giving you the perfect balance of strength and maneuverability.
The MLOK slots on the side and bottom of the rail allow you to attach your favorite accessories, making customization easy and effective. Whether you're looking to add a flashlight, bipod, or anything in between, the MLOK slots give you the versatility to get the job done right.
Starting from the trigger guard, you'll have about 15.25 inches of arca rail below allowing you to position a bipod further out. Additionally, the 1/4-20 threads on the bottom of the chassis allow for easy attachment to a camera tripod adapter.
Finally, the quick disconnect holes located on both sides of the chassis make it easy to attach a sling, adding an additional layer of comfort and convenience to your shooting experience.
Overall, the Saber Tactical Raw HM1000 chassis is the perfect upgrade for anyone looking to take their air rifle performance to the next level. So why wait? Order yours today and get ready to take on the competition with confidence and style!
DonnyFL
DonnyFL | RYU Moderator
$166.49
$184.99
FEATURES:• Indexed locking system for consistent position and no point of impact changes.• Quick detachment for easy storage and reattachment for shooting.• Comes with a 1/2 x 20 female (barrel/shroud) thread adapter.• Modular design for length adjustment.• Crafted from 6061 T6 aluminum (individual sections) and 7075 aluminum (main QD housing andadapter).• Quick disconnect rear available for the following moderators.(EMPEROR,SUMO,RONIN,SHOGUN,FX,TANTO,TATSU,KOI,FATBOY)
The RYU has the same diameter as our KOI at 30.48mm or 1.2 inches.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
Saber Tactical
Panthera Rail - ST0057
$292.50
$325.00
Panthera Rail - ST0057
PRODUCT DESCRIPTION
Our Saber Tactical Panthera rail has already proven itself in competition helping our shooters bring home the gold in PRS competitions. It adds the rigidity and weight needed to shoot accurately in different positions.
Features:
The main body is made of lightweight T6 aluminum.
Removable brass inserts for added weight
Mlok slots on the side allow shooters to add more weight to their setup
Allows you to use a 300cc bottle when the middle brass weight is removed. Will require Panthera front bottle adapter ST0056.
Jimping pattern underneath the rail to help grip shooting bags
Wider than the factory rail
Length = 17.71 in, Width = 1.96 in
Weight = 4 pounds
Add an extra pound of weight with our brass bridge ST0059
DonnyFL
DonnyFL | RONIN Moderator
$166.49
$184.99
Ronin is big and bold, but it looks great even on compact bullpups. "Maybe a little overkill for the .177 and .22 but it looks so damn awesome!" - Donny
Available in .25/.30 and .357 (Big Bore) calibers
2 x 6.5 inches
1/2 x 20 UNF, FX(20mm) & Vulcan thread by request.
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become lose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
Saber Tactical
Saber Tactical | 50MM BOTTLE CLAMP ST0071
$53.99
$59.99
PRODUCT DESCRIPTION
If you're uneasy about drilling into your factory gun stock, this 50mm bottle clamp will easily attach to your 50mm carbon fiber or aluminum bottles. It has rubber pads on the inside to prevent any marring to your bottle.
This clamp has picatinny rails at the bottom for you to connect your preferred picatinny accessories.
-Great fit for the Umarex Gauntlet 30.
Features:
6061 T6 aluminum
Matte black anodize
Saber Tactical
Extended Dust Cap Cover ST0019
$8.99
$9.99
This extended dust cap makes it easier to get into those tight trigger guards. With this dust cap, you can easily remove without straining your finger muscles!
Features:
Made of aluminum 60601 with a strong magnet inside
Measures: 14mm outer diameter and just shy of 23mm long
Western Airguns
Western Airguns | Rattler Moderator Adapter | M18X1
$40.49
$44.99
Western Airguns Rattler Moderator Adapter M18x1
Saber Tactical
Saber Tactical | Huben GK1 Stock/Brace Adapter ST0085
$31.50
$35.00
PRODUCT DESCRIPTION
Since the Huben GK1 was released, customers have asked for a way to add a buttstock to their pistols. The wait is over. Introducing the Saber Tactical Huben GK1 Stock/Brace Adapter!
Key Features:
Versatile Attachment: Bolt on a rear-facing Picatinny rail and attach any number of folding or rigid stocks to your GK1, increasing stability and accuracy for longer shots.
Quick Installation: The SBA connects to your GK1 with two elongated stainless steel screws (included), replacing the stock screws. Installation requires only 2mm and 4mm Allen wrenches (not included) and takes just a few minutes.
Dual Functionality: Once installed, you can use the airgun in pistol or carbine format without removing the adapter and without losing any of the GK1's functionality.
High-Quality Construction: Machined from 6065 aluminum and anodized black to match the Huben. It sits like a Picatinny backpack on the rear of the action, above the grip's beavertail, leaving full access to the grip, loading mechanism, and iron sights, including elevation adjustment.
Important Information:
Buttstock Sold Separately: Choose from a variety of folding or rigid stocks to customize your setup.
Saber Tactical
Panthera Brass Bridge - ST0059
$112.50
$125.00
PRODUCT DESCRIPTION
Add an additional pound of weight with our brass bridge. Only compatible with our Saber Panthera rail since ours is wider than factory rail.
Features:
MLok slots on top allowing you to attach different accessories.
Weight: 1 lb
DonnyFL
Western Airguns | Sidewinder Adapter | A109
$53.99
$59.99
Product description
Experience the Ultimate Shooting Upgrade with the Western Airguns Sidewinder Adapter by DonnyFL!
Elevate your airgun game to new heights with our innovative Sidewinder Adapter, designed to give you the perfect fusion of performance, compatibility, and durability. Experience unmatched shooting prowess as you pair your favorite silencers or moderators with high-powered air rifles like never before.
Product Features:
Exclusive Pre-Production Offer: Be the first to test out this cutting-edge technology with our special pre-production, non-anodized version of the Sidewinder adapter.
Unparalleled Durability: Crafted from high-quality 6061 aluminum, ensuring long-lasting performance and reliability.
Wide Compatibility: Designed for .22 to .30 caliber airguns, making it a versatile and indispensable addition to your shooting arsenal.
Exceptional Performance: Experience improved accuracy and noise reduction with seamless integration of your favorite silencers or moderators.
Note: Not compatible with the Rattler model.
Don't miss this limited-time opportunity to upgrade your airgun performance with the Western Airguns Sidewinder Adapter from DonnyFL
DonnyFL
DonnyFL | GREAT KAMI Moderator
$256.49
$284.99
When we first released the Emperor, we never thought there would be a demand for something longer. But now with the .72 cal Zeus on the market, the Great Kami is born.
The baffles are thicker compared to the Emperor to withstand the constant powerful air blast, yet it only weighs 2 more ounces than the Emperor.
Features:
Enhanced Durability: Thicker baffles than the Emperor to withstand the constant powerful air blasts, yet only 2 ounces heavier.
High-Quality Construction: Made from 6061 T6 aluminum and black anodized for maximum durability.
Lightweight: Weighs just 1.2 lbs for easy handling.
Threaded Compatibility:
.72 cal Zeus is threaded M23x1 specifically for the AEA Zeus.
.45 to .58 cal is threaded M18x1.
DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.